Dimensions / Weight

	W	H	D
Dimensions	142.5 mm (5.61 inch)	124 mm (4.88 inch)	350 mm (13.78 inch)

Weight : Approx.5.5 kg(12.13 lbs)

DC Power Supply PWR-01 Series

Compact, wide-range DC power supply

PWR-01 Series – 800W model

PWR-01-800W

183,000円 – 243,000円

Sequence function (supports triggered synchronization)
Variable internal resistance function
LAN (LXI compliant) /USB/RS232C as standard interface
A virtual multi-channel bus (VMCB) function makes multi-channel operation more efficient
A wide range of voltage and current settings can be combined within its output power rating (3 to 4 times)
Supporting universal input voltage (85 V to 265 V)
CONFIG setting shortcut function and display (Up to three parameters can be registered.)
Setting preset memory function (3 combinations of settings for voltage, current, OVP, OCP, and UVL)
Bleeder (sink) can be turned ON/OFF, with an even stronger bleeder mode setting available
Output ON/OFF delay function
Soft start/stop function
Durable Performance Operating temperature guaranteed up to 50 °C (122 °F). (Storage temperature is -25 °C to +60 °C (-13 °F to 140 °F).)

SKU	Output CV [V]	Output CC [A]	Output Power [W]	標準価格
PWR801L	0 to 40V	0 to 80A	800W	183,000円（税込：201,300円）
PWR801ML	0 to 80V	0 to 40A	800W	183,000円（税込：201,300円）
PWR801MH	0 to 240V	0 to 10A	800W	233,000円（税込：256,300円）
PWR801H	0 to 650V	0 to 3.70A	800W	243,000円（税込：267,300円）

SKU: PWR-01-800W

Line-up

SKU	Output CV [V]	Output CC [A]	Output Power [W]	標準価格
PWR801L	0 to 40V	0 to 80A	800W	183,000円（税込：201,300円）
PWR801ML	0 to 80V	0 to 40A	800W	183,000円（税込：201,300円）
PWR801MH	0 to 240V	0 to 10A	800W	233,000円（税込：256,300円）
PWR801H	0 to 650V	0 to 3.70A	800W	243,000円（税込：267,300円）

Specifications

800W model

AC input

Open in a new window ZOOM

Item/Model		PWR801L
Nominal input rating		100 Vac to 240 Vac, 50 Hz to 60 Hz, single phase
Input voltage range		85 Vac to 265 Vac
Input frequency range		47 Hz to 63 Hz
Current (TYP) *1	100 Vac	11.2 A
Current (TYP) *1	200 Vac	5.6 A
Inrush current		50 A or less
Power (MAX) *2		1120 VA
Power factor (TYP) *1		0.99 (input voltage: 100 V), 0.97 (input voltage: 200 V)
Efficiency (TYP) *1		75%
Output hold time *2		20 ms or more

*1. At the rated output power for the rated output current. *2. 100 Vac, at the rated output power.

Output

Open in a new window ZOOM

Item/Model			PWR801L	PWR801ML	PWR801MH	PWR801H
Rating	Output voltage*1		40 V	80 V	240 V	650 V
	Output current*1		80 A	40 A	10 A	3.70 A
	Output power		800 W
Voltage	Maximum settable voltage*2		42 V	84 V	252 V	682.5 V
	Accuracy		±（0.05 % of setting +0.05 % of rating）
	Resolution		200 mV	400 mV	1000 mV	2500 mV
		Using FINE, OUT OFF	10 mV	10 mV	100 mV	100 mV
		Using FINE, OUT ON	1 mV	1 mV	10 mV	10 mV
		When using a communication interface	0.1 mV	0.1 mV	0.1 mV	0.1 mV
	Line regulation *3		± 6 mV	± 10 mV	± 26 mV	± 67 mV
	Load regulation *4		± 6 mV	± 10 mV	± 26 mV	± 67 mV
	Transient response *5		1 ms or less	2 ms or less	2 ms or less	3 ms or less
	Ripple noise *6	p-p*7	50 mV	50 mV	100 mV	300 mV
	Ripple noise *6	rms*8	5 mV	5 mV	20 mV	50 mV
	Rise time	At full load	50 ms or less		100 ms or less
	Rise time	No load	50 ms or less		100 ms or less
	Fall time *9	At full load	50 ms or less		150 ms	250 ms
	Fall time *9	No load	500 ms or less		1200 ms	2000 ms
	Maximum remote sensing compen- sation voltage (single line)		1.5 V	4 V	5 V	5 V
	Temperature coefficient *10		100 ppm/ ℃
Current	Maximum settable current *2		84 A	42 A	10.5 A	3.885 A
	Setting accuracy *11		±（0.5 % of setting +0.1 % of rating）
	Resolution		400 mA	200 mA	40 mA	20 mA
		Using FINE, OUT OFF	10 mA	10 mA	10mA	1 mA
		Using FINE, OUT ON	1 mA	1 mA	1 mA	0.1 mA
		When using a communication interface	0.1 mA	0.1 mA	0.1 mA	0.1 mA
	Power fluctuation		± 10 mA	± 6 mA	± 3 mA	± 2.4 mA
	Load variation		± 21 mA	± 13 mA	± 7 mA	± 5.7 mA
	Ripple noise *12	rms*8	160 mA	80 mA	24 mA	12 mA
	Rise time (TYP)	At full load	50 ms		100 ms
	Fall time (TYP)	At full load	50 ms		100 ms
	Temperature coefficient *10		100 ppm/ ℃
Maximum internal resistance that can be set			0.500 Ω	2.000 Ω	18.00 Ω	131.8 Ω

*1 The maximum output voltage and maximum output current are limited by the maximum output power. *2 Can be limited to approximately 95 % of the OVP trip point or OCP trip point. *3 85 Vac to 135 Vac or 170 Vac to 265 Vac, fixed load. *4 The amount of change that occurs when the load is changed from no load to full load (rated output power/rated output voltage) with rated output voltage. The value is measured at the sensing point. *5 The amount of time required for the output voltage to return to a value within “rated output voltage ± (0.1 % +10 mV).” The load current fluctuation is 50 % to 100 % of the maximum current with the set output voltage. *6 Measured using an RC-9131C probe that conforms to the JEITA specifications. At the rated output current. *7 When the measurement frequency bandwidth is 10 Hz to 20 MHz. *8 When the measurement frequency bandwidth is 10 Hz to 1 MHz. *9 When the bleeder circuit is set to bleeder normal. *10 When the ambient temperature is within 0°C and 50 °C. *11 Applies to the range of 1 % to 100 % of the rated current. TYP (0.1 % of rating) for 0 % to 1 %. *12 When the output voltage is 10 % to 100 % of the rating. At the rated output current.

別ウインドウで開く

Item/Model			PWR801L	PWR801ML	PWR801MH	PWR801H
Rating	Output voltage*1		40 V	80 V	240 V	650 V
	Output current*1		80 A	40 A	10 A	3.70 A
	Output power		800 W
Voltage	Maximum settable voltage*2		42 V	84 V	252 V	682.5 V
	Accuracy		±（0.05 % of setting +0.05 % of rating）
	Resolution		200 mV	400 mV	1000 mV	2500 mV
		Using FINE, OUT OFF	10 mV	10 mV	100 mV	100 mV
		Using FINE, OUT ON	1 mV	1 mV	10 mV	10 mV
		When using a communication interface	0.1 mV	0.1 mV	0.1 mV	0.1 mV
	Line regulation *3		± 6 mV	± 10 mV	± 26 mV	± 67 mV
	Load regulation *4		± 6 mV	± 10 mV	± 26 mV	± 67 mV
	Transient response *5		1 ms or less	2 ms or less	2 ms or less	3 ms or less
	Ripple noise *6	p-p*7	50 mV	50 mV	100 mV	300 mV
	Ripple noise *6	rms*8	5 mV	5 mV	20 mV	50 mV
	Rise time	At full load	50 ms or less		100 ms or less
	Rise time	No load	50 ms or less		100 ms or less
	Fall time *9	At full load	50 ms or less		150 ms	250 ms
	Fall time *9	No load	500 ms or less		1200 ms	2000 ms
	Maximum remote sensing compen- sation voltage (single line)		1.5 V	4 V	5 V	5 V
	Temperature coefficient *10		100 ppm/ ℃
Current	Maximum settable current *2		84 A	42 A	10.5 A	3.885 A
	Setting accuracy *11		±（0.5 % of setting +0.1 % of rating）
	Resolution		400 mA	200 mA	40 mA	20 mA
		Using FINE, OUT OFF	10 mA	10 mA	10mA	1 mA
		Using FINE, OUT ON	1 mA	1 mA	1 mA	0.1 mA
		When using a communication interface	0.1 mA	0.1 mA	0.1 mA	0.1 mA
	Power fluctuation		± 10 mA	± 6 mA	± 3 mA	± 2.4 mA
	Load variation		± 21 mA	± 13 mA	± 7 mA	± 5.7 mA
	Ripple noise *12	rms*8	160 mA	80 mA	24 mA	12 mA
	Rise time (TYP)	At full load	50 ms		100 ms
	Fall time (TYP)	At full load	50 ms		100 ms
	Temperature coefficient *10		100 ppm/ ℃
Maximum internal resistance that can be set			0.500 Ω	2.000 Ω	18.00 Ω	131.8 Ω

Display function

Open in a new window ZOOM

Item/Model		PWR801L	PWR801MH	PWR801H
Voltage display	Maximum display	99.99	999.9
Voltage display	Display accuracy	± (0.2 % of reading +5 digits)
Current display	Maximum display	99.99		9.999
Current display	Display accuracy	± (0.5 % of reading +8 digits)
Power display		The PWR DSPL LED lights in red.
	Maximum display	9999
	Display accuracy	Displays the result of multiplying the current and voltage. The display is toggled with the voltage or current display.

Unless specified otherwise, the specifications are for the following settings and conditions.
Loads are pure resistive loads. ●The product is warmed up for at least 30 minutes (with current flowing). ●After warm-up, the product must be calibrated correctly in a 23 °C ± 5 °C environment according to the appropriate calibration procedure. ●Values indicated by “TYP” are typical values. They are not guaranteed performance values. ●Values indicated by “rating” are ratings. ●Values indicated by “reading” are readings. ●Values indicated by “f.s.” are full scale values. ●The PWR-01 operates over a wide range of output voltage and output current within rated output power. However, the current that can be output with rated output voltage and the voltage that can be output with rated output current are limited by the rated output power. ●The current that can be output with rated output voltage and the voltage that can be output with rated output current are as follows. Maximum output current with rated output voltage = Rated output power/ rated output voltage. Maximum output voltage with rated output current = Rated output power/ rated output current. ●Rated load and no load are defined as follows:In constant-voltage mode (when the output current is set to a value greater than or equal to the maximum output current with rated output voltage) Rated load: Refers to a resistive load that, when the rated output voltage is applied,makes the flowing current 95 % to 100 % of the maximum output current with rated output voltage.No load:Refers to a load through which no output current flows. In other words,refers to an open load (no load being connected). In constant-current mode (when the output voltage is set to a value greater than or equal to the maximum output voltage with rated output current) Rated load:Refers to a resistive load that, when the rated output current flows, makes the voltage drop to 95 % to 100 % of the maximum output voltage with rated output current. Including the voltage drop in the load cables, the PWR-01 output voltage must not exceed the maximum output voltage with rated output current. No load:Refers to a resistive load that, when the rated output current flows, makes the voltage drop to 10 % of the maximum output voltage with rated output current or 1 V whichever is higher. ●The specifications of the PWR-01 apply to the rear-panel output terminals.

Common specifications

Protection functions

Open in a new window ZOOM

Item/Model		400W
Overvoltage protection (OVP)		Turns the output off *1, displays OVP, and lights ALM
	Selectable range	10 % to 112 % of the rated output voltage
	Setting accuracy	±（1.5 % of rating）
Overcurrent protection (OCP) *2		Turns the output off *1, displays OCP, and lights ALM
	Selectable range	10 % to 112 % of the rated output voltage
	Setting accuracy	±（3 % of rating）
Front-panel output terminal overcurrent protection (FOCP)*3		Turns the output off *1, displays FOCP, and lights ALM
Front-panel output terminal overcurrent protection (FOCP)*3	Value (fixed)	11 A (TYP)
Undervoltage limit (UVL)		Cannot be set to a value less than or equal to the set voltage
Undervoltage limit (UVL)	Selectable range	0 % to 105 % of the rated output voltage
Overheat protection (OHP)		Turns the output off, displays OHP, and lights ALM
Incorrect sensing connection protection (SENSE)		Turns the output off, displays SENS, and lights ALM
Low AC input protection (AC-FAIL)		Turns the output off *4, displays AC, and lights ALM
Shutdown (SD)		Turns the output off *1, displays SD, and lights ALM
Power limit (POWER LIMIT)		ALM blinking
Power limit (POWER LIMIT)	Value (fixed)	Approx. 105% of the rated output power
Communication monitoring (watchdog)		Turns the output off, displays WDOG, and lights ALM
Master-slave parallel operation protection (PRL ALM)		Turns the output off *1, displays PRL, and lights ALM

*1. Output off or breaker trip on the 2000 W model. *2. This does not protect against the discharge current peak that is generated from the capacitors inside the PWR-01 output section when the load is changed suddenly. *3. Available on models with a maximum settable current of 11 A or more. If the OCP value is less than the FOCP value, the OCP value takes precedence. *4. Auto recovery after eliminating the cause of the alarm is selectable.

Signal output and input

Open in a new window ZOOM

Item/Model			400W
Monitor signal output	Voltage monitor (VMON)		Selectable monitor voltage range: 0 V to 5 V or 0 V to 10 V
	Voltage monitor (VMON)	Setting accuracy	2.5 % of f.s. *1
	Current monitor (IMON)		Selectable monitor voltage range: 0 V to 5 V or 0 V to 10 V
	Current monitor (IMON)	Setting accuracy	2.5 % of f.s. *1
Status signal output *2	OUTON STATUS		On when output is on.
	CV STATUS		Turns on during CV operation
	CC STATUS		Turns on during CC operation
	ALARM STATUS		Turns on when an alarm has been activated
	POWER ON STATUS		Turns on when the power is turned on
Trigger signal	Input (TRG IN)		Logic selectable: LOW (0 V to 1.5 V), HIGH (3.5 V to 5 V)
	Input (TRG IN)		Input impedance: 10 kΩ (TYP)
	Output (TRG OUT)		Logic selectable: LOW (0 V to 0.6 V), HIGH (4.2 V to 5 V)
	Output (TRG OUT)		Pulse width: 100 μs (TYP)

*1. f.s. is the full scale at the selected range. It is 10 V for the 10 V range and 5 V for the 5 V range. *2. Photocoupler open collector output; maximum voltage 30 V, maximum current (sink) 8 mA; isolated from the output and control circuits; status commons are floating (withstand voltage of less than or equal to 60 V); and status signals are not mutually isolated.

Control functions

Open in a new window ZOOM

Item/Model			400W
External control	Output voltage control (VPGM)		0 % to 100 % of the rated output voltage
			Selectable control voltage range: 0 V to 5 V or 0 V to 10 V
		Accuracy	5 % of rating
	Output current control (IPGM)		0 % to 100 % of the rated output current
			Selectable control voltage range: 0 V to 5 V or 0 V to 10 V
		Accuracy	5 % of rating
	Output on/ off control OUTPUT ON/OFF CONT		Logic selectable: Output on when set to LOW (0 V to 0.5 V) or shorted; output off when set to HIGH (4.5 V or 5 V) or open Output on when set to HIGH (4.5 V to 5 V) or open; output off when set to LOW (0 V or 0.5 V) or shorted
	Output shutdown control SHUT DOWN		Output on when set to LOW (0 V to 0.5 V) or shorted
	Alarm clear control ALM CLR		Alarm cleared when set to LOW (0 V to 0.5 V) or shorted

Other functions

Open in a new window ZOOM

Item/Model		400W	1200W
Output-on/ off delay		Setting range: 0.0 s, 0.5 s to 99.9 s *1 setting resolution: 0.1 s
Soft start and soft stop		Setting range: 0.0 s, 0.5 s to 10.0 s *1 setting resolution: 0.1 s
Overcurrent protection (OCP) activation delay		Setting range: 0.0 s to 2.0 s *1 setting resolution: 0.1 s
Preset memory		Up to three sets of the following settings can be saved: the set voltage, the set current, the set OVP, the set OCP, and the set UVL.
key lock		Locks the operation of all keys other than the OUTPUT key.
CONFIG shortcut		Up to three CONFIG parameters can be registered to the SC1, SC2, and SC3 keys
Sequence		Number of programs: 1
		Number of steps: 64
		Repetition count: 1 to 99998, INFinity
		Number of configurable interval loops: 16
		Number of interval loops: 2 to 99998
		Step time: 0.1 s to 100 h (common to step transition and ramp transition)
Synchronized Operation		Synchronization of voltage and current settings, synchronization of the resumption of steps in a sequence program
Master-slave parallel operation *2		Up to three units (same models) including the master unit	Up to two units (same models) including the master unit
Series operation *3		Two units (the same model)
Multichannel (VMCB)	Connection between the master unit and PC	LAN, USB, RS232C
Multichannel (VMCB)	Connection with slave units	LAN

*1. Factory default is 0.0 s. *2. Current difference between the master and slaves is 5 % (TYP). *3. H type is excluded

Operation display

Open in a new window ZOOM

Item/Model		400W
OUTPUT ON/OFF		OUTPUT LED lights green when the output is on.
Output-on/ off delay		“DLY” lights when it is set and blinks when it is in effect. OUTPUT LED blinks orange while outputon delay is in effect.
Output-on/ off delay		OUTPUT LED blinks green while output-off delay is in effect.
Soft start and soft stop		“SS” lights when it is set and blinks when it is in effect. OUTPUT LED lights green when soft start is in effect. OUTPUT LED blinks green when soft stop is in effect.
CV operation		CV LED lights in green.
CC operation		CC LED lights in red.
Alarm operation		ALM LED lights in red when a protection function has been activated. ALM LED blinks red when the power limit (POWER LIMIT) is activated. OUTPUT LED blinks orange when a protection function is activated when the output is on.
Preset memory		PRESET A, B, or C LED lights green when a preset memory entry is being recalled or saved.
Key lock operation		LOCK LED lights green when the keys are locked.
Remote operation		REMOTE LED lights green during remote control.
Remote operation	LAN operation	LAN LED lights or blinks depending on the status. No fault status: Lights green. Fault status: red. Standby status: Lights orange. WEB identify status: Blinks green.
Bleeder circuit		“HB” lights when the hyper bleeder is set.
Variable internal resistance (VIR)		“VIR” lights when it is set.
Sequence		“SEQ” lights when a sequence is being executed and blinks the PWR-01 is waiting for a trigger.

Interface

Open in a new window ZOOM

Item/Model		400W
Common specifications	Software protocol	IEEE Std 488.2-1992
Common specifications	Command language	Complies with SCPI Specification 1999.0
RS232C	Hardware	Complies with the EIA232D specifications (excluding the connector)
		RJ-45 connector (male) *1
		Baud rate: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps
		Data length: 8 bits, Stop bits: 1 bit, Parity bit: None
		No flow control
	Program message terminator	LF during reception, CR/LF during transmission
USB	Hardware	Complies with the USB 2.0 specifications; data rate: 480 Mbps (HighSpeed)
	Hardware	Socket B type
	Program message terminator	LF or EOM during reception, LF + EOM during transmission
	Device class	Complies with the USBTMC-USB488 device class specifications
LAN	Hardware	IEEE 802.3 100Base-TX/10Base-T Ethernet
		Complies with LXI Specification2011 Ver.1.4
		Complies with LXI HiSLIP Extended Function Rev.1.01
		IPv4, RJ-45 connector *2
	Communication protocol	VXI-11, SCPI-RAW, HiSLIP
	Program message terminator	VXI-11, HiSLIP: LF or END during reception, LF + END during transmission SCPI-RAW: LF during reception, LF during transmission.

*1. The RD-8P/9P adapter cable is an option. *2. Category 5; use a straight cable.

General

Open in a new window ZOOM

Item/Model		400W	800W	1200W	2000W
Weight (main unit only)		Approx. 3 kg (6.61 lb)	Approx. 5.5 kg (12.13 lb)	Approx. 7.5 kg (16.53 lb)	Approx. 13 kg (28.66 lb)
Dimensions		See the outline drawing.(Catalogue p15)
Environmental conditions	Operating environment	Indoor use, overvoltage category II
	Operating temperature	0 °C to +50 °C (32 °F to +122 °F)
	Operating humidity	20 %rh to 85 %rh (no condensation)
	Storage temperature	-25 °C to +60 °C (-13 °F to 140 °F)
	Storage humidity	90 %rh or less (no condensation)
	Altitude	Up to 2000 m
Cooling method		Forced air cooling using fan
Grounding polarity		Negative grounding or positive grounding possible
Isolation voltage		L/ ML/ MH type: ±500 Vmax H type: ±800 Vmax
Withstanding voltage	Across the primary circuit and chassis	No abnormalities when 1500 Vac is applied for 1 minute
	Across the primary and secondary circuits	L/ ML/ MH type: No abnormalities when 1650 Vac is applied for 1 minute
	Across the primary and secondary circuits	H type: No abnormalities when 1900 Vac is applied for 1 minute
	Across the secondary circuit and chassis	L/ ML/MH type: No abnormalities when 2300 Vdc is applied for 1 minute
	Across the secondary circuit and chassis	H type: No abnormalities when 2640 Vdc is applied for 1 minute
Insulation resistance	Across the primary circuit and chassis	100 MΩ or more (70 %rh or less) at 500 Vdc
	Across the primary and secondary circuits	LL/ ML/ MH type: 100 MΩ or more (70 %rh or less) at 500 Vdc
	Across the primary and secondary circuits	H type: 100 MΩ or more (70 %rh or less) at 1000 Vdc
	Across the secondary circuit and chassis	L/ ML/ MH type: 40 MΩ or more (70 %rh or less) at 500 Vdc
	Across the secondary circuit and chassis	H type: 40 MΩ or more (70 %rh or less) at 1000 Vdc
Accessories		Operation Manuals Chassis connection short bar Output terminal M4 screws (2 pcs.) Output terminal cover Output terminal bolt set (2 sets) M8 bolt set (For 400 W, 800 W and 1200 W model) M10 bolt set (For 2000 W model) Only L type and ML type included. Power cord Included only with the 400 W/800 W model Input terminal cover Included only with the 1200 W model Ferrite core set Included only with the 1200 W model
Electromagnetic compatibility 1 2		Complies with the requirements of the following directive and standard. EMC Directive 2014/30/EU EN61326-1 (Class A 3), EN 55011 (Class A 3, Group 1 *4), EN 61000-3-2 EN 61000-3-3 Applicable under the following conditions: The maximum length of all cabling and wiring connected to the product must be less than 3 m.
Safety *1		Complies with the requirements of the following directive and standard. Low Voltage Directive 2014/35/EU 2 EN 61010-1 (Class I 5 , Pollution Degree 2 *6)

*1. Does not apply to specially ordered or modified products. *2. Limited to products that have a CE mark. Does not apply unless a core is attached to the J1 connector cable. *3. This is a Class A instrument. This product is intended for use in an industrial environment. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts. *4. This is a Group 1 instrument. This product does not generate and/or use intentionally radiofrequency energy, in the form of electromagnetic radiation, inductive and/or capacitive coupling, for the treatment of material or inspection/analysis purpose. *5. This is a Class I instrument. Be sure to ground this product’s protective conductor terminal. The safety of this product is guaranteed only when the product is properly grounded. *6. Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduction of dielectric strength or surface resistivity. Pollution Degree 2 assumes that only nonconductive pollution will occur except for an occasional temporary conductivity caused by condensation.

別ウインドウで開く

Item/Model		400W	800W	1200W	2000W
Weight (main unit only)		Approx. 3 kg (6.61 lb)	Approx. 5.5 kg (12.13 lb)	Approx. 7.5 kg (16.53 lb)	Approx. 13 kg (28.66 lb)
Dimensions		See the outline drawing.(Catalogue p15)
Environmental conditions	Operating environment	Indoor use, overvoltage category II
	Operating temperature	0 °C to +50 °C (32 °F to +122 °F)
	Operating humidity	20 %rh to 85 %rh (no condensation)
	Storage temperature	-25 °C to +60 °C (-13 °F to 140 °F)
	Storage humidity	90 %rh or less (no condensation)
	Altitude	Up to 2000 m
Cooling method		Forced air cooling using fan
Grounding polarity		Negative grounding or positive grounding possible
Isolation voltage		L/ ML/ MH type: ±500 Vmax H type: ±800 Vmax
Withstanding voltage	Across the primary circuit and chassis	No abnormalities when 1500 Vac is applied for 1 minute
	Across the primary and secondary circuits	L/ ML/ MH type: No abnormalities when 1650 Vac is applied for 1 minute
	Across the primary and secondary circuits	H type: No abnormalities when 1900 Vac is applied for 1 minute
	Across the secondary circuit and chassis	L/ ML/MH type: No abnormalities when 2300 Vdc is applied for 1 minute
	Across the secondary circuit and chassis	H type: No abnormalities when 2640 Vdc is applied for 1 minute
Insulation resistance	Across the primary circuit and chassis	100 MΩ or more (70 %rh or less) at 500 Vdc
	Across the primary and secondary circuits	LL/ ML/ MH type: 100 MΩ or more (70 %rh or less) at 500 Vdc
	Across the primary and secondary circuits	H type: 100 MΩ or more (70 %rh or less) at 1000 Vdc
	Across the secondary circuit and chassis	L/ ML/ MH type: 40 MΩ or more (70 %rh or less) at 500 Vdc
	Across the secondary circuit and chassis	H type: 40 MΩ or more (70 %rh or less) at 1000 Vdc
Accessories		Operation Manuals Chassis connection short bar Output terminal M4 screws (2 pcs.) Output terminal cover Output terminal bolt set (2 sets) M8 bolt set (For 400 W, 800 W and 1200 W model) M10 bolt set (For 2000 W model) Only L type and ML type included. Power cord Included only with the 400 W/800 W model Input terminal cover Included only with the 1200 W model Ferrite core set Included only with the 1200 W model
Electromagnetic compatibility 1 2		Complies with the requirements of the following directive and standard. EMC Directive 2014/30/EU EN61326-1 (Class A 3), EN 55011 (Class A 3, Group 1 *4), EN 61000-3-2 EN 61000-3-3 Applicable under the following conditions: The maximum length of all cabling and wiring connected to the product must be less than 3 m.
Safety *1		Complies with the requirements of the following directive and standard. Low Voltage Directive 2014/35/EU 2 EN 61010-1 (Class I 5 , Pollution Degree 2 *6)