PBZ Series
よくあるご質問 閲覧ランキング
- 耐電圧(耐圧)試験って何ですか?
- 直流電源を接続する配電盤のブレーカ選定について教えてください。
- 検査票、試験成績書、校正証明書、トレーサビリティ証明書について教えてください。
- 電波法の高周波利用設備に該当する製品はありますか。
- VISAライブラリについて教えてください。
- ウォームアップ時間はどれくらいですか。
- 製品に電安法適用表示(PSEマーク)がありません。違法ではないですか。
- 耐電圧試験器を操作するために、必要な資格はありますか。
- PWR-01シリーズのPOWER スイッチをオンにしても動作しません。どうしたら良いでしょうか。
- 製品におけるPCB含有の有無について教えてください。
- マニュアル通りにコマンドを送っているのですが動作しません。どうしたらよいでしょうか。
- What is the input voltage for PBZ series?
- What is the setting accuracy of the constant current (CC) for PBZ series?
- Is PBZ series available with an optional LAN interface?
- What is the SCPI ERR -220 in PBZ series?
- When the pin No.3 and 7 (shutdown signal) of the J1 connector of PBZ series is short-circuited, is the POWER switch turned off?
- What is the slew rate of the output voltage for PBZ series?
- What is Wavy for PBZ Ver. 6.X? I use Wavy for PBZ Ver. 6.22. Is it considered Ver. 6.X?
- Can PBZ series perform the parallel operation in the unipolar mode?
- What happens to the sequence operation of PBZ series performed by Wavy for PBZ if the PC stops or communication is interrupted?
- What cables are used for the J1 connector of PBZ series?
- Can PBZ series perform the ramp transition (rising and falling)?
- Are there any restrictions on firmware version when operating PBZ series in parallel?
- Can Wavy for PBZ be used for PBZ SR series?
- Can PBZ series remotely enable/disable the remote sensing?
- Can PBZ series clear the alarm by external control via the J1 connector?
- What is the performance when two PBZ series units are connected in parallel?
- What is the relationship between the output on/off via external control and the output on/off setting of the sequence operation in PBZ series?
- Why cannot I turn off the output of PBZ series when I abort the sequence on Wavy for PBZ?
- Is it possible to use PBZ series with floating output without connecting the COM terminal to the chassis terminal?
- Can PBZ series load and save a sequence data?
- Can PBZ series stop the square wave output at a specified time?
- Can PBZ series synchronize the sequence operation without using a PC?
- Can PBZ series synchronize and sequence-control the output from the multiple units?
- Can the sweep setting for the AC signal frequency be configured to 1000 s or longer in PBZ series?
- How do I control PBZ series by an external voltage via the J1 connector?
- Can the ramp setting for the DC signal in the sequence step be configured to 1000 s or longer in PBZ series?
- Can the sweep setting for the AC signal amplitude be configured to 1000 s or longer in PBZ series?
- How can I set the offset using the EXT SIG IN signal in PBZ series?
- Why cannot I set the voltage while PBZ series displays the current value?
- Does PBZ series have a setting where the output is automatically turned on when the POWER switch is turned on?
- What is the command to clear alarms for PBZ series?
- How do I restart PBZ series when the POWER switch is turned off by a shutdown?
- Can I use Wavy for PBX for PBZ series?
- Can PBZ series turn off the POWER switch (breaker trip) by a shutting down signal via the external contact?
- Is it possible to disable the OVP and OCP functions of PBZ series?
- How do I turn off the output of PBZ series in case of an abnormality?