Item | PLZ1005WH2 | PLZ2005WH2 | PLZ4005WH2 | PLZ12005WH2 | PLZ20005WH2 | |
---|---|---|---|---|---|---|
Input voltage range | 100 Vac to 240 Vac (90 Vac to 250 Vac) single phase | |||||
Input frequency range | 47 Hz to 63 Hz | |||||
Power consumption | 70 VAmax | 90 VAmax | 150 VAmax | 360 VAmax | 590 VAmax | |
Inrush current (peak value) | 100 Vac | 30 Amax | 30 Amax | 30 Amax | 40 Amax | 40 Amax |
230 Vac | 80 Amax | 80 Amax | 80 Amax | 160 Amax | 160 Amax | |
Leakage current*1 | 0.5 mA or less | 0.6 mA or less | 0.8 mA or less | 1.6 mA or less | 2.4 mA or less | |
Environmental conditions | Operating temperature range | 0 °C to 40 °C (32 °F to 104 °F) | ||||
Operating humidity range | 20 %rh to 85 %rh (no condensation) | |||||
Storage temperature range | -25 °C to 60 °C (-13 °F to 140 °F) | |||||
Storage humidity range | 90 %rh or less (no condensation) | |||||
Installation location | Indoor use, altitude of up to 2000 m, overvoltage category II | |||||
Insulation resistance | Between primary and chassis, input, monitor terminals | 1000 Vdc, 30 MΩ or more (70 %rh or less) | ||||
Between input terminals and chassis, monitor terminal | 1000 Vdc, 3 MΩ or more (70 %rh or less) | |||||
Withstanding voltage | Between primary and chassis, input, monitor terminals | No abnormalities at 1500 Vac for 2 s | ||||
Between input terminals and chassis, monitor terminal | No abnormalities at 1500 Vac for 2 s | |||||
Weight | Approx. 13 kg (28.66 lb) | Approx. 16 kg (35.3 lbs) | Approx. 20 kg (44.1 lbs) | Approx. 64 kg (141.1 lbs) | Approx. 93 kg (205 lbs) | |
Accessories | [Common to all models] Power cord (1 pc., length: 2.5 m), Safety terminal adapter TL41 (red 1 set, black 1set), External control connector kit (1 set), Safety Information (1 copy), Setup Guide (1 copy), Quick Reference (Japanese 1 sheet, English 1 sheet), CD-ROM (1 disc) [PLZ1005WH2, PLZ2005WH2, PLZ4005WH2] Rear-panel DC INPUT terminal cover (1 set), Screw set for rear-panel DC INPUT terminals (2 sets), Screws for the rear-panel DC INPUT terminal cover (2 pcs.) , Front-panel DC INPUT terminal cover (1 pc.), Screws for the front-panel DC INPUT terminals (2 pcs.) , Heavy object warning label (1 pc.) PLZ4005WH2 only [PLZ12005WH2, PLZ20005WH2] Rear-panel DC INPUT terminals cover (1 set), Screw set for rear-panel DC INPUT terminals (2 sets), Rear-panel DC INPUT terminals cover screws (2 pcs.), Heavy object warning label (1 pc.), Parallel operation signal cable kit [PC02-PLZ-5W] | |||||
Electromagnetic compatibility (EMC) *2 *3 | Conforms to the requirements of the directive and standard below. EMC Directive 2014/30/EU EN 61326-1 (Class A *4), EN 55011 (Class A *4, Group 1 *5), EN 61000-3-2, EN 61000-3-3 Applicable under the following conditions The maximum length of all cabling and wiring connected to the product must be less than 3 m. | |||||
Safety *2 | Conforms to the requirements of the directive and standard below. EMC Directive 2014/35/EU *3 EN 61010-1 (Class I *6, Pollution Degree 2 *7) |
* 1. Leakage current between the positive and negative terminals of the rear-panel DC INPUT. At 1000 Vdc. * 2. Does not apply to specially ordered or modified products. * 3. Limited to models that have a CE mark on their panels. * 4. This is a Class A instrument. This product is intended for use in an industrial environment. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts. * 5. This is a Group 1 instrument. This product does not generate and/or use intentionally radio-frequency energy, in the form of electromagnetic radiation, inductive and/or capacitive coupling, for the treatment of material or inspection/analysis purpose. * 6. This is a Class I instrument. Be sure to ground this product’s protective conductor terminal. The safety of this product is guaranteed only when the product is properly grounded. * 7. Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduction of dielectric strength or surface resistivity. Pollution Degree 2 assumes that only non-conductive pollution will occur except for an occasional temporary conductivity caused by condensation.